
Tyre size comparison: diameter, sidewall and calculated speed changes
Enter two tyre sizes to compare diameter, circumference, width and sidewall height. The tool also shows a geometric change in ground clearance and calculated speed when the speedometer reads 100 km/h, assuming calibration for the reference size.
The comparison is geometric only and does not approve a size, installation or licensing. The speed figure is calculated assuming calibration for the reference size, not a measurement of actual speed.
How to use the tool
- Enter tyre width in mm, aspect ratio as a percentage and rim diameter in inches for the reference size.
- Enter the second size in the same units and press compare.
- Read the diameter and circumference changes and sidewall height, not just the rim size.
- Before changing the car, check the vehicle licence (רישיון רכב) and ask a testing centre (מכון רישוי) about approval and registration of the appropriate size.
Three numbers define a tyre size
For width, enter millimetres; for aspect ratio, enter sidewall height as a percentage of width; and for the rim, enter its diameter in inches. The aspect ratio is not sidewall height in millimetres. Two tyres with the same aspect ratio but different widths therefore do not necessarily have the same sidewall height. The calculator breaks down the size so that you can compare the components themselves.
Copy the numbers accurately and keep the sizes in the intended order: the first is the comparison baseline, and the second is assessed against it. Swapping them changes both the direction of the difference and the basis for the percentages. A tyre already fitted to a car is not, by itself, proof that its size is registered or approved for that vehicle.
A larger rim does not determine the overall diameter on its own
The calculated overall diameter comprises the rim diameter and two tyre sidewalls, one at each end of the diameter. Increasing the rim while reducing the sidewall can leave a similar overall diameter, but you cannot infer that from the last number in the size alone. Compare the total result and the percentage difference after entering all the figures.
The tool also displays circumference and width. The geometric ground clearance change is half the diameter change, assuming everything else stays the same. This is not a complete calculation of the car's actual height, and it does not check the suspension or clearance around the wheel. The result describes nominal dimensions, not a measurement of a specific tyre under load.
The resulting speed is a calculated scenario
The figure beside a reading of 100 km/h is based on the circumference ratio between the two sizes. It assumes the speedometer is calibrated for the reference size and does not add any existing system error. A larger circumference covers more distance per revolution, so the ratio changes the calculated speed for the same reading.
The calculator does not measure vehicle speed or calibrate the speedometer. Do not use the result to decide that you can exceed the permitted speed as shown on the dashboard, or to conclude that a particular car's reading is accurate. A value close to the reference size means the geometric difference is small; it does not prove suitability or compliance with licensing requirements.
Size approval is checked separately from geometry
Before replacement, check the tyre size recorded on the vehicle licence. The Ministry of Transport and Road Safety procedure includes a testing-centre process to verify a tyre size change against appropriate approval data and complete its registration. If the size you are considering is not listed, ask the centre what your car requires before making the change. The calculator's percentage difference is not an approval.
Even a similar geometric result does not check rim compatibility, clearances, load and speed ratings or manufacturer requirements. The tool does not receive all those details and therefore cannot approve installation. Save both sizes and the results for a professional discussion; decisions about suitability and registration must be based on the vehicle and its documents.
Questions and answers
- What does the aspect ratio percentage mean?
- It is tyre sidewall height as a proportion of width. The same percentage applied to two different widths can give two different sidewall heights.
- Does an almost identical diameter mean the size is permitted?
- No. The calculation does not grant fitment or licensing approval. Check the licence and ask a testing centre what is needed to approve and register a change.
- Is the number beside 100 km/h my actual speed?
- It is a calculated speed based on the circumference ratio, assuming calibration for the reference size. The tool does not measure the car and does not know its existing speedometer error.
- Why is the ground clearance change smaller than the diameter change?
- The geometric calculation uses the radius change, which is half the diameter change. It does not include tyre behaviour under load or other changes to the car.
- Can this tell me whether a tyre suits the rim and vehicle weight?
- No. The tool compares dimensions only. It does not check rim compatibility, load and speed ratings or the car's other requirements.